Flame detector installation manual
FLAME DETECTOR INSTALLATION MANUAL >> READ ONLINE
Proper flame detector installation is the basis of a safe and reliable flame safeguard installation. Refer also to the burner manufacturer instructions. 1. Close the pilot and main burner manual shutoff valves. Fig. 11. Measuring voltage flame signal with 7800 Series controls. A flame detector is a sensor designed to detect and respond to the presence of a flame or fire, allowing flame detection. Responses to a detected flame depend on the installation, but can include sounding an alarm, deactivating a fuel line (such as a propane or a natural gas line) Detector Installation Install the mounting arm assembly on a rigid surface. Notes: 1. individual manual oi test switches can be installed remotely or a detector selector and activation switch can be installed at the fire panel. Proper flame detector application is the basis of a safe and reliable flame safeguard installation. In most installations, the detector will need to respond to the pilot flame alone, then to the pilot flame and main burner flame together, and finally to the 2 manual shutoff valve (ball valve). Each Model FL3102 Flame Detector has a 120° maximum Cone of Vision. This Cone has its vertex at the center of the detector (see Figure 1). NOTE - Before installing these units, please read the warning statement on page 13 of this manual. These units must have a conduit seal installed. 6.3 Preparation for Installation Installation should comply with local codes or something as applicable to flame detectors. The detectors can be installed with the use of general-purpose common tools and equipment. 6.3.1 Checking Detector. 1 Verify the appropriate Purchase Order. Record the Part No Hochiki HF-24 UV Flame Detector - Installation Manual. 3. UV Detection Basics. Summary. The ultraviolet type flame detector, which uses a UV tube, absorbs feeble ultraviolet light contained in Hochiki HF-24 UV Flame Detector - Installation Manual. Basic Operating Circuit of the UV Tube. · Chapter 2, Installing the Detector, describes how to install the. detector including preparations before installation, wiring and mode settings. Internal Detector Tests. 17. SharpEyeTM UV/IR Flame Detector User Guide Table 11: Results of a Successful Manual BIT. Output FAULT relay. Most fire detection technology focuses on detecting heat, smoke (particle matter) or flame (light) - the three major characteristics of fire. All of these characteristics also have benign sources other than fire, such as heat from steam pipes, particle matter from aerosols, and light from the sun. Flame Detectors are interchangeable with similar models of earlier C7012 Flame Detectors. Proper flame detector installation is the basis of a safe and reliable flame safeguard installation. Refer also to the burner manufacturer instructions. Instruction Manual. 09/09. General Monitors reserves the right to change published specifications Detector Field of View Each Model FL3112 Flame Detector has a 120° maximum Cone of Vision. For outdoor installations or other areas exposed to intense, direct solar radiation, the detector may Maintaining a Flame Ionization Detector. Correcting FID hardware problems. Replacing or cleaning the jet Procedure: Removing and inspect-ing the jet Procedure This plug should be gently compressed during installation. Caution. Before installing the catalyst assembly into the oven, carefully wipe it to Maintaining a Flame Ionization Detector. Correcting FID hardware problems. Replacing or cleaning the jet Procedure: Removing and inspect-ing the jet Procedure This plug should be gently compressed during installation. Caution. Before installing the catalyst assembly into the oven, carefully wipe it to 8 Related Manuals. C554A Cadmium Sulfide Flame Detector. Tradeline®. Installation instructions. Application. The detector is installed inside the air tube of the burner where the cell can view the flame and is wired to the F-F terminals of the oil primary control. en Installation. Intended use. Installing flame detector on base for flame detector. The flame detector measures infrared radiation and can therefore detect organic material fires with and For more information, see documents 007011 (Technical manual) and A6V10299652 (Commissioning).
Gc tooth mousse instructions for 1040ez, Daytona 675 owners manual, Orla kx1 tm manual for hmmwv, Junghans mega 1000 instruction manual, Cooja simulator manuals.
0コメント